Målet med examensarbetet var att kontrollera noggrannheten i de handberäknade diagrammen för kalkcementpelarförstärkning och hur de står sig mot dagens beräkningar i programmet Slope/W. Diagrammen skall även digitaliseras för att underlätta översiktlig dimensionering av kalkcementpelarförstärkning.Examensarbetet har utförts genom att fyra utvalda exempel valts ut från det handberäknade diagrammet, sedan har datorberäkningar gjorts i programmet Slope/W för att kontrollera noggrannheten och den procentuella skillnaden mellan metoderna. Utöver jämförelsen av c-analyserna och digitaliseringen av det, har ett översiktligt diagram för att underlätta beräkningar av kalkcementpelarförstärkning för c?-analys skapats. Detta har skapats som komplement till det handberäknade diagrammet och kan användas vid översiktlig dimensionering av kalkcementpelarförstärkning.

The sandy beaches of Vänern are threatened by overgrowth and thereby the biodiversity is at high risk to decline. This study is based on an inventory of vegetation of overgrowth character and mosses. The frequency and spread of mosses is perceived as an indication of initial or present overgrowth. External factors that have been taken into consideration are wind-, wave- and ice erosion, the slope of the beach, wear and grade of exposure. The purpose of the investigation is to control the beaches grade of overgrowth and find out which external factor is of most importance for the maintenance of the biotope. The results show that the beaches environment is affected by the slope of the beach, grade of exposure, size, wear and overgrowth.

This thesis is written on behalf of Skanska, Väg- och Anläggning Stockholm Mälardalen, vid Nya Karolinska Sjukhuset i Solna, NKS. The report has resulted in recommendations for the method of soil stabilizations of soil nailing, excavation of slope and fiber reinforced shotcrete, which is the most suitable method from a safety and a cost point at the NKS.The aim of this thesis was to investigate whether fiber reinforced shotcrete increases slope stability, with the focus being on the total stability. The main goal was to investigate which method of soil stabilization is the most suitable for the slopes that are analyzed in this report. Through studying literature, the authors have gained an understanding about the theoretical background for the given problem. Through calculations and analyses of the slopes, safety factors have been acquired.

The interaction between the driver, the car and the road is essential for the road safety. This case study focuses on the road condition and its effect regarding road safety issues. By studying and isolating the road condition aspect and its contributing role to the accident occurrence, the aim is to explore their relationship, as well as highlight the road parameters that are commonly associated with accident occurrence. This result will be used to develop and increase awareness of the impact of poor road alignment and poor road surface conditions on traffic safety, in order to prevent these accidents from occurring. The road parameters chosen for this study include side friction, cross slope and rut bottom cross slope, road texture, curvature, drainage gradient and rutting.The case study was limited to lv 360 in Va?sterbotten, where all accidents with an unclear cause of the accident were studied, between 2003 and 2012 were carefully studied and assessed based on the condition of the road at the time of the accident.

This paper is a literature review that examines how good mental calculation skills benefit pupils, which could work as a valuable learning tool for future teachers. The study addresses four key questions: ?What are the advantages of proficient mental calculations??, ?What strategies exist for mental calculation skills??, ?How can teachers accommodate their teaching to develop pupils? mental calculation skills?? and ?What has arithmetic looked like in different eras and what algorithms have been used??. Through literature searches in search engines, scientific articles were found, which formed the basis for the result segment. This was divided into two parts: A historical and a didactic overview.

The purpose of this report is to survey Swedex AB?s production costs and to gather all info into a manageable calculation tool. This was made by time and motion studies, interviews of the personnel. All factors were gathered into an Excel chart.The calculation was made according to an additional-charge-method that was considered to satisfy Swedex AB?s goal.

Chunks and Tasks is a programming model based on the C ++ programming language. This programming model is used for electronic structure calculations, among other things.The purpose of this project is to improve the CHT-MPI software library for Chunks and tasks, so that calculations of matrix-matrix multiplications are performed more efficiently than they do with the existing software library. The software library is based on the work stealing method, which is a method the software library for Chunks and Tasks uses for the distribution of the calculation work. The considered way to improve the software library is by modifying the work stealing method in a way that makes the distribution of calculation work happen in a more efficient way , which will lead to calculations performed faster than before.Two different modifications of the work stealing method were tested and it led to two new methods, Method 1 and Method 2, which distributed the calculation work differently. Method 1 did not give results that were compatible with the theory, since the calculation time with this method was much longer than the previous method.

Energy costs are high nowadays and that is the reason why the energy consumption needs to become as small as possible in most of the companies. To accomplish the small energy usage one needs to map the energy flows, study them and monitor them. One method that can be used for this is energy balance calculation. The method gives an opportunity to separate different energy flows and see where each flow is heading. There is also another method which is more advanced than energy balance calculation.

The purpose with this work is to investigate the cost to produce piglet in a case study company. The starting point is going to be the agriwise (www.agriwise.org) calculation which I am going to change and adapt to the case study company. To day the pig market is bad but we have probably reached the bottom. The market has started to rise. It is no business to produce piglets today.

A common problem in forestry is plant death caused by frost. The risk of frost is highest on wind protected, flat or low-lying areas in the terrain. Here you often have regeneration problems with Norwegian spruce which is especially sensitive to spring frost. Swedish tree experiments have shown that the black spruce can be a suitable alternative on these areas, for example on moisture frost prone areas. The species originates from North America and its pioneer tree characteristics make it more frost hardy than Norwegian spruce.

This report is about the shear force design of reinforced concrete according to Europe?s common dimension rules, Eurocode. The purpose is to describe the calculation procedure and the background to the formulas and expressions that occurs. Furthermore results from different calculation methods (hand calculations and computer calculations) will be compared to see how they differ.The goal with this is to go through the parts of Eurocode dealing with shear force and that this will lead to a clear review of these. You should also be able to see how results and the calculation procedure differ between different calculation methods.

This report is about the shear force design of reinforced concrete according to Europe?s common dimension rules, Eurocode. The purpose is to describe the calculation procedure and the background to the formulas and expressions that occurs. Furthermore results from different calculation methods (hand calculations and computer calculations) will be compared to see how they differ.The goal with this is to go through the parts of Eurocode dealing with shear force and that this will lead to a clear review of these. You should also be able to see how results and the calculation procedure differ between different calculation methods.

The report contains three parts. The first part is a summary and overall presentation of thermalcracks and preventing measures against such cracks. This is a theoretical part where theinterested designer can get acquainted with various alternatives, be guided to more detailedliterature, and receive some practical information regarding the design of the respectivemeasures.The second part deals with calculation of the risk for thermal cracks and design of water coolingas a limiting measure. Two complementary methods are reviewed for efficient calculation:?the handbook method CraX1(by Lulea University of Technology) is used for quickverification?finite differential analysis in the calculationtool ConTeSt Pro for more precise projectingHere is also presented a development of existing standards through design of the cooling systemby means of the Bernoulli equation.

The globalization that has occurred during the last few years has made it more important for companies to have a well-functioning logistics system. Customers demand more options, which lead to an increased flow that creates greater demand regarding packaging and transports. Diverse logistics costs are nowadays a substantial cost for many companies. Therefore, more effort is aimed at optimizing transportation to lower these costs.The purpose of this project is to create a user-friendly calculation of logistics costs that illustrates how the costs vary, depending on how the flow is structured. This is done by examining which aspects that affect the total logistics costs and by mapping which aspects that should be included in a calculation of the logistics costs.Literature studies have been carried out parallel with empirical studies at Scania's production unit, MC, in Oskarshamn.

The purpose of this paper is to standardize and simplify the design work on a few specific types of storage brackets for balconies. The company Balco AB had the wish to simplify the design work in the preparation of attachments to their balcony structures. This would be done by a calculation matrix that could be produced which then in turn could be used for each new project by the company. The design work behind the development of these fittings at each new project is costly both in terms of time devoted by each calculation but also the cost of the time. The purpose of this report is that in a systematic manner, a calculation matrix can be created that then the company instead may follow from each new project.In carrying out the project used HILTI calculation program, which was provided by the company HILTI.